GT-AX6000路由器WAN口和LAN口短接后无法拨号
家里弱电箱比较小，现在的网络结构是，光猫LAN1接交换机LAN1，交换机LAN2接路由器LAN2，交换机LAN3、LAN4接其他房间的设备，路由器WAN和路由器LAN1短接，之前用网件R8500时，可以正常拨号，所有设备都能上网，最近更换了GT-AX6000后，路由器拨号一直无法成功，大佬们能否帮忙分析下日志，看有没有解决的办法，万分感谢Mar 28 15:54:37 dnsmasq: nameserver 202.103.24.68 refused to do a recursive query
Mar 28 16:00:53 disk_monitor: Got SIGALRM...
Mar 28 16:03:28 kernel: eth0 (Int switch port: 5) (Logical Port: 5) (phyId: 11) Link DOWN.
Mar 28 16:03:28 kernel: ^[ xport_reset: rc = 0; intf = 1 port = 0 spd = 1G dup = 1
Mar 28 16:03:28 kernel: ^[[0m
Mar 28 16:03:30 WAN Connection: Fail to connect with some issues.
Mar 28 16:03:32 kernel: MACSEC: macsec is not enabled
Mar 28 16:03:33 kernel: ^[ xport_init: rc = 0; intf = 1 port = 0 spd = 2.5G dup = 1
Mar 28 16:03:33 kernel: ^[[0m
Mar 28 16:03:33 kernel: eth0 (Int switch port: 5) (Logical Port: 5) (phyId: 11) Link Up at 2500 mbps full duplex
Mar 28 16:03:35 kernel: ^[ xport_init: rc = 0; intf = 3 port = 2 spd = 2.5G dup = 1
Mar 28 16:03:35 kernel: ^[[0m
Mar 28 16:03:35 kernel: eth5 (Int switch port: 6) (Logical Port: 6) (phyId: 13) Link Up at 2500 mbps full duplex
Mar 28 16:03:35 WAN Connection: WAN(0) link up.
Mar 28 16:03:35 rc_service: wanduck 20907:notify_rc restart_wan_if 0
Mar 28 16:03:42 kernel: netlink: 12 bytes leftover after parsing attributes in process `ip'.
Mar 28 16:03:43 pppd: pppd 2.4.7 started by hwvbrbsc, uid 0
Mar 28 16:03:47 kernel: eth4 (Int switch port: 3) (Logical Port: 3) (phyId: 4) Link Up at 1000 mbps full duplex
Mar 28 16:04:18 pppd: Timeout waiting for PADO packets
Mar 28 16:05:33 pppd: Timeout waiting for PADO packets
Mar 28 16:05:44 wlceventd: wlceventd_proc_event(508): eth7: Disassoc 42:B2:5E:B7:72:28, status: 0, reason: Disassociated because sending station is leaving (or has left) BSS (8), rssi:0
Mar 28 16:05:44 wlceventd: wlceventd_proc_event(508): eth7: Disassoc 42:B2:5E:B7:72:28, status: 0, reason: Disassociated because sending station is leaving (or has left) BSS (8), rssi:0
Mar 28 16:06:14 rc_service: httpd 21238:notify_rc start_lltdc
Mar 28 16:06:14 kernel: netlink: 12 bytes leftover after parsing attributes in process `ip'.
Mar 28 16:06:14 kernel: netlink: 12 bytes leftover after parsing attributes in process `ip'.
Mar 28 16:06:14 kernel: netlink: 12 bytes leftover after parsing attributes in process `ip'.
Mar 28 16:06:14 kernel: netlink: 12 bytes leftover after parsing attributes in process `ip'.
Mar 28 16:06:18 rc_service: httpd 21238:notify_rc start_lltdc
Mar 28 16:06:48 pppd: Timeout waiting for PADO packets
Mar 28 16:08:03 pppd: Timeout waiting for PADO packets
Mar 28 16:09:18 pppd: Timeout waiting for PADO packets
Mar 28 16:10:33 pppd: Timeout waiting for PADO packets
Mar 28 16:11:48 pppd: Timeout waiting for PADO packets
Mar 28 16:13:04 pppd: Timeout waiting for PADO packets
Mar 28 16:14:19 pppd: Timeout waiting for PADO packets
Mar 28 16:15:09 wlceventd: wlceventd_proc_event(491): eth6: Deauth_ind 38:81:D7:2A:47:60, status: 0, reason: Unspecified reason (1), rssi:0
Mar 28 16:15:09 wlceventd: wlceventd_proc_event(527): eth6: Auth 38:81:D7:2A:47:60, status: Successful (0), rssi:0
Mar 28 16:15:09 wlceventd: wlceventd_proc_event(556): eth6: Assoc 38:81:D7:2A:47:60, status: Successful (0), rssi:-56
Mar 28 16:15:09 wlceventd: wlceventd_proc_event(491): eth6: Deauth_ind 38:81:D7:2A:47:60, status: 0, reason: Unspecified reason (1), rssi:0
Mar 28 16:15:10 wlceventd: wlceventd_proc_event(527): eth6: Auth 38:81:D7:2A:47:60, status: Successful (0), rssi:0
Mar 28 16:15:10 wlceventd: wlceventd_proc_event(556): eth6: Assoc 38:81:D7:2A:47:60, status: Successful (0), rssi:-56
Mar 28 16:15:34 pppd: Timeout waiting for PADO packets
提示什么错误..截个图发上来..账号密码错误? b31shimp5 发表于 2022-3-29 08:12
提示什么错误..截个图发上来..账号密码错误?
账号密码没问题，光猫直接连WAN口可以正常拨号 LAN-IPTV设定页
Choose IPTV STB Port选“LAN1 & LAN2” WAN和LAN短接当然有问题啦.... Master 发表于 2022-3-29 10:00
LAN-IPTV设定页
Choose IPTV STB Port选“LAN1 & LAN2”
用你说的这个配置后，可以正常拨号了，无线端的设备上网也都OK，太感谢了:handshake不过又发现了另外一个问题，连接交换机LAN3、LAN4接口的设备没法从路由器自动获取IP地址了，手动指定IP地址后，也不能上网，是不是还需要做一些其他的设置呢？ hwvbrbsc 发表于 2022-3-29 19:59
用你说的这个配置后，可以正常拨号了，无线端的设备上网也都OK，太感谢了不过又发现了另外一 ...
交换机的LAN1 & LAN2，LAN3 & LAN4要切成两组VLAN。切完后，GT-AX6000的LAN3接交换机的LAN3，然后交换机的LAN4上的设备才能获得GT-AX6000分出的IP。
交换机怎么切VLAN，具体自己再搜一下相关内容。 也是同样的问题，一模一样。现在在LAN-IPTV设定页
Choose IPTV STB Port选“LAN1 & LAN2”后，连接交换机LAN3、LAN4接口的设备没法从路由器自动获取IP地址了，手动指定IP地址后，也不能上网。请问楼主最终是怎么解决的？我之前用红米AX6000这些，只用把其中一个口固定为WAN口，然后WAN口和LAN口短接就行，华硕路由器麻烦了。
hwvbrbsc 发表于 2022-3-29 19:59
用你说的这个配置后，可以正常拨号了，无线端的设备上网也都OK，太感谢了不过又发现了另外一 ...
请问你最终怎么解决的？
页:
[1]