TUF-AX3000路由器 无线无法跑满1000M 只能跑300
我家联通宽带升级到1000M了可是我发现TUF-AX3000路由器只能跑到300M的速度
家里电脑是INTEL AX200 WiFi6 无线网卡
路由器用的都是六类线
联通光猫也带无线WiFi6的功能 ，用光猫无线测速有700M以上的速度
TUF-AX3000有线连接路由器的时候可以跑到1000M左右
如图：我在路由器的管理界面-QoS网络监控界面-网络测速 可以看到下载速度是930M
可是TUF-AX3000无线的测速只有300M
我在设置里面已经把QoS网络安全等等这些能关闭的都关闭了，速度几乎没有变化。
问客服也是没啥用，都是官方那些什么升级固件，重置，这些都试过了。
这是我的5G WiFi配置
Jan 18 12:27:15 rc_service: ntp 2056:notify_rc restart_diskmon
Jan 18 12:27:15 disk_monitor: Finish
Jan 18 12:27:15 disk monitor: be idle
Jan 18 12:27:16 kernel: Archer TCP Pure ACK Enabled
Jan 18 12:27:16 dhcp client: bound 192.168.1.2/255.255.255.0 via 192.168.1.1 for 86400 seconds.
Jan 18 12:27:17 cfg_server:event: wl_chanspec_changed_action
Jan 18 12:27:17 cfg_server: skip event due no re
Jan 18 12:27:46 cfg_server:event: wl_chanspec_changed_action
Jan 18 12:27:46 cfg_server: current chansp(unit0) is 1003
Jan 18 12:27:46 cfg_server: current chansp(unit1) is e32a
Jan 18 12:27:46 cfg_server: dump exclchans:
Jan 18 12:27:46 cfg_server: old wl0_acs_excl_chans:0x100c,0x190a,0x100d,0x190b,0x100e,0x190c
Jan 18 12:27:46 cfg_server: new wl0_acs_excl_chans:0x100e,0x190c
Jan 18 12:27:46 cfg_server: old wl1_acs_excl_chans:0xd0a5
Jan 18 12:27:46 cfg_server: new wl1_acs_excl_chans:0xd034,0xd038,0xd03c,0xd040,0xd836,0xd936,0xd83e,0xd93e,0xe03a,0xe13a,0xe23a,0xe33a,0xec32,0xed32,0xee32,0xef32
Jan 18 12:27:46 cfg_server:wl_chanspec_changed_action: Need to restart acsd for AVBL update
Jan 18 12:27:46 rc_service: cfg_server 1787:notify_rc restart_acsd
Jan 18 12:27:46 acsd: eth5: Selecting 2g band ACS policy
Jan 18 12:27:51 acsd: eth5: selected channel spec: 0x1003 (3)
Jan 18 12:27:51 acsd: eth5: Adjusted channel spec: 0x1003 (3)
Jan 18 12:27:51 acsd: eth5: selected channel spec: 0x1003 (3)
Jan 18 12:27:51 acsd: eth6: Selecting 5g band ACS policy
Jan 18 12:27:53 crond: time disparity of 1949722 minutes detected
Jan 18 12:27:53 acsd: eth6: selected channel spec: 0xea32 (44/160)
Jan 18 12:27:53 acsd: eth6: Adjusted channel spec: 0xea32 (44/160)
Jan 18 12:27:53 acsd: eth6: selected channel spec: 0xea32 (44/160)
Jan 18 12:27:55 wlceventd: wlceventd_proc_event(527): eth5: Auth EC:4D:3E:5E:C5:E2, status: Successful (0), rssi:0
Jan 18 12:27:55 wlceventd: wlceventd_proc_event(556): eth5: Assoc EC:4D:3E:5E:C5:E2, status: Successful (0), rssi:-40
Jan 18 12:27:57 wlceventd: wlceventd_proc_event(527): eth6: Auth 7C:10:C9:5A:67:D4, status: Successful (0), rssi:-36
Jan 18 12:27:57 wlceventd: wlceventd_proc_event(556): eth6: Assoc 7C:10:C9:5A:67:D4, status: Successful (0), rssi:-39
Jan 18 12:27:57 kernel: Register interface MAC: d4:5d:64:92:e3:ac
Jan 18 12:28:02 wlceventd: wlceventd_proc_event(527): eth5: Auth 40:31:3C:CB:1F:02, status: Successful (0), rssi:0
Jan 18 12:28:02 wlceventd: wlceventd_proc_event(556): eth5: Assoc 40:31:3C:CB:1F:02, status: Successful (0), rssi:-63
Jan 18 12:29:01 WATCHDOG: periodic_check AM 3:56
Jan 18 12:29:01 WATCHDOG: fimrware update check first time
Jan 18 12:29:01 WATCHDOG: notify_rc firmware_webs_update
Jan 18 12:29:01 rc_service: watchdog 1413:notify_rc firmware_webs_update
Jan 18 12:29:15 wlceventd: wlceventd_proc_event(527): eth6: Auth 08:5B:D6:C8:98:21, status: Successful (0), rssi:-50
Jan 18 12:29:15 wlceventd: wlceventd_proc_event(556): eth6: Assoc 08:5B:D6:C8:98:21, status: Successful (0), rssi:-51
Jan 18 12:29:36 kernel: SHN Release Version: 2.0.2 d2ff630
Jan 18 12:29:36 kernel: UDB Core Version: 0.2.20
Jan 18 12:29:36 kernel: sizeof forward pkt param = 192
Jan 18 12:29:36 BWDPI: fun bitmap = 3
Jan 18 12:29:48 BWDPI: force to flush flowcache entries
Jan 18 12:29:48 BWDPI: rollback fc
Jan 18 12:30:25 wlceventd: wlceventd_proc_event(491): eth6: Deauth_ind 08:5B:D6:C8:98:21, status: 0, reason: Unspecified reason (1), rssi:-50
Jan 18 12:30:25 wlceventd: wlceventd_proc_event(527): eth6: Auth 08:5B:D6:C8:98:21, status: Successful (0), rssi:-50
Jan 18 12:30:25 wlceventd: wlceventd_proc_event(556): eth6: Assoc 08:5B:D6:C8:98:21, status: Successful (0), rssi:-50
Jan 18 12:31:01 wlceventd: wlceventd_proc_event(491): eth6: Deauth_ind 08:5B:D6:C8:98:21, status: 0, reason: Unspecified reason (1), rssi:-54
Jan 18 12:31:01 wlceventd: wlceventd_proc_event(527): eth6: Auth 08:5B:D6:C8:98:21, status: Successful (0), rssi:-54
Jan 18 12:31:01 wlceventd: wlceventd_proc_event(537): eth6: ReAssoc 08:5B:D6:C8:98:21, status: Successful (0), rssi:-54
Jan 18 12:31:04 wlceventd: wlceventd_proc_event(491): eth6: Deauth_ind 7C:10:C9:5A:67:D4, status: 0, reason: Deauthenticated because sending station is leaving (or has left) IBSS or ESS (3), rssi:-42
Jan 18 12:31:04 wlceventd: wlceventd_proc_event(491): eth6: Deauth_ind 7C:10:C9:5A:67:D4, status: 0, reason: Deauthenticated because sending station is leaving (or has left) IBSS or ESS (3), rssi:-42
Jan 18 12:31:05 wlceventd: wlceventd_proc_event(508): eth6: Disassoc 7C:10:C9:5A:67:D4, status: 0, reason: Disassociated because sending station is leaving (or has left) BSS (8), rssi:0
Jan 18 12:31:13 wlceventd: wlceventd_proc_event(527): eth6: Auth 7C:10:C9:5A:67:D4, status: Successful (0), rssi:-32
Jan 18 12:31:13 wlceventd: wlceventd_proc_event(556): eth6: Assoc 7C:10:C9:5A:67:D4, status: Successful (0), rssi:-36
Jan 18 12:31:14 kernel: Register interface MAC: d4:5d:64:92:e3:ac 私信我留微信.我给你看看 先到TUF-AX3000，System Log-Wireless Log页面确认一下你Intel AX200的连线速度。 Master 发表于 2022-1-18 15:18
先到TUF-AX3000，System Log-Wireless Log页面确认一下你Intel AX200的连线速度。
应该跟AX200无线网卡的连接速度没关系，我看网卡的握手速度是1.2G，有时候是1.4G 。
而且我用手机iPhone X测试速度和电脑测试速度差不多，都是200-300M之间。但是换到光猫的WiFi上，直接提到400-600M。(电脑距离光猫较远，信号衰减严重) dlam128 发表于 2022-1-18 16:00
应该跟AX200无线网卡的连接速度没关系，我看网卡的握手速度是1.2G，有时候是1.4G 。
而且我用手机iPhone X ...
无线专业设置页面，把区域调成“澳大利亚”。 Master 发表于 2022-1-18 15:18
先到TUF-AX3000，System Log-Wireless Log页面确认一下你Intel AX200的连线速度。
SSID: "Lc"
noise: -80 dBm Channel: 2
BSSID: D4:5D:64:92:E3:A8 Capability: ESS RRM
Supported Rates: [ 1(b) 2(b) 5.5(b) 6 9 11(b) 12 18 24 36 48 54 ]
HE Capable:
Chanspec: 2.4GHz channel 2 20MHz (0x1002)
Primary channel: 2
HT Capabilities: 40Mhz SGI20 SGI40
Supported HT MCS : 0-15
Supported VHT MCS:
NSS1 Tx: 0-11 Rx: 0-11
NSS2 Tx: 0-11 Rx: 0-11
Supported HE MCS:
80 Mhz:
NSS1 Tx: 0-11 Rx: 0-11
NSS2 Tx: 0-11 Rx: 0-11
Interference Level: Acceptable
Mode : AP Only
Stations List
----------------------------------------
idx MAC Associated Authorized RSSI PHY PSM SGI STBC MUBF NSS BW Tx rate Rx rate Connect Time
B2:B1:04:7E:86:29 Yes Yes -46dBm n Yes Yes YesNo 120M 72.2M 11M 00:03:50
E8:AB:FA:47:CD:DF Yes Yes -48dBm n NoYes No No 120M 65M 1M 00:04:53
EC:4D:3E:5E:C5:E2 Yes Yes -43dBm n Yes Yes YesNo 120M 72.2M 6M 00:05:00
40:31:3C:CB:1F:02 Yes Yes -67dBm n NoYes YesNo 120M 72.2M 36M 00:05:00
SSID: "Lc"
noise: -87 dBm Channel: 40/160
BSSID: D4:5D:64:92:E3:AC Capability: ESS RRM
Supported Rates: [ 6(b) 9 12(b) 18 24(b) 36 48 54 ]
HE Capable:
Chanspec: 5GHz channel 50 160MHz (0xe932)
Primary channel: 40
HT Capabilities: 40Mhz SGI20 SGI40
Supported HT MCS : 0-31
Supported VHT MCS:
NSS1 Tx: 0-11 Rx: 0-11
NSS2 Tx: 0-11 Rx: 0-11
NSS3 Tx: 0-11 Rx: 0-11
NSS4 Tx: 0-11 Rx: 0-11
Supported HE MCS:
80 Mhz:
NSS1 Tx: 0-11 Rx: 0-11
NSS2 Tx: 0-11 Rx: 0-11
NSS3 Tx: 0-11 Rx: 0-11
NSS4 Tx: 0-11 Rx: 0-11
160 Mhz:
NSS1 Tx: 0-11 Rx: 0-11
NSS2 Tx: 0-11 Rx: 0-11
NSS3 Tx: 0-11 Rx: 0-11
NSS4 Tx: 0-11 Rx: 0-11
Interference Level: Acceptable
Mode : AP Only
DFS status: state In-Service Monitoring(ISM) time elapsed 256650ms radar channel cleared by DFS channel 40/160 (0xE932)
Channel Information
----------------------------------------
Channel 36 A Band
Channel 40 A Band
Channel 44 A Band
Channel 48 A Band
Channel 52 A Band, RADAR Sensitive
Channel 56 A Band, RADAR Sensitive
Channel 60 A Band, RADAR Sensitive
Channel 64 A Band, RADAR Sensitive
Channel 149 A Band
Channel 153 A Band
Channel 157 A Band
Channel 161 A Band
Channel 165 A Band
Stations List
----------------------------------------
idx MAC Associated Authorized RSSI PHY PSM SGI STBC MUBF NSS BW Tx rate Rx rate Connect Time
7C:10:C9:5A:67:D4 Yes Yes -40dBm axNoYes YesYes 280M 1201.0M 1201.0M 00:04:07
08:5B:D6:C8:98:21 Yes Yes -56dBm axNoYes YesYes 2 160M 1201.0M 1441.2M 00:04:13
这个是日志……看不太懂
Master 发表于 2022-1-18 17:57
无线专业设置页面，把区域调成“澳大利亚”。
设置了 默认就是澳大利亚 把QoS关了，博通的ARM不开硬NAT，性能和MIPS一样 看到你的5G设置自动选择了153信道，高信道是否不支持160M啊？试试手动指定低信道，比如36、44什么的。
页:
[1]
2